Large Character Inkjet Printer

The PZ Pilot Pro hi-resolution ink jet printing system offers 2.1" print height from a single print head with the ability to run up to 4 print heads from a single controller. The PZ Pilot Pro offers a versatile, yet cost effective solution for your coding applications. The PZ Pilot Pro utilizes 380 print heads that print up to 2.1" in height, exceeding the GS1 specification for case code printing without the additional cost of a larger print head. Industry proven piezo technology produces razor-sharp text and dark print for increased bar code scannability.    Print Technology Piezo impulse printhead technology Printheads Up to four high resolution, 380 channelpiezo printheads Maximum Print Height 2.1″ (53.3 mm) per 380 printhead,meets GS1 specification for case code printing Vertical Print Resolution 180 dpi capable of printing razorsharpgraphics, small character text, and scannable bar codes Horizontal Print Resolution 180 dpi Print Speed Up to 167 feet/minute @ 180 dpi with380 printhead Time & Date Internal real time clock with battery back-up Product Sensor Reflective sensor standard with dual photocellinputs standard Communication Interface Four USB host, ethernet Touchscreen 6.4″ color display Ink System Active ink system; dual 400ml ink canister standard Low Ink Indicator Warning messages alert user on thetouchscreen display, LED beacon optional Substrate Capabilities  Porous surfaces  Cabinet Construction Stainless steel, solvent-resistant colortouchscreen display      Electrical Requirements  90 – 264 VAC, 50/60 Hz     Operating Environment  50°F - 104°F (10°C - 40°C)     Storage Environment  0°F - 140°F (-18°C - 60°C)   

AutoPilot printing system will print up to .7″ of hi-resolution characters, razor-sharp text, scannable bar codes, and great looking logos. Users can run up to two printheads from a single touchscreen controller to maximize efficiency and print on opposite sides of a case if needed. The AutoPilot is capable of running oil-based or solvent-based inks to print on a variety of substrates. Best of all, AutoPilot’s 180 dpi print resolution meets your application needs for quality coding and marking.     Print Technology Piezo impulse printhead technology Maximum Print Height .7" (1.8cm) per printhead Vertical Print Resolution 180 dpi capable of printing razor-sharp graphics, small character text, and scannable bar codes Horizontal Print Resolution 180 dpi Print Speed Up to 135 feet/min. (41 m/min.) @ 180 dpi Time & Date Internal real time clock with battery back-up Product Sensor Built in product sensors, optional external photocell Communication Interface Two USB host and one ethernet input Touchscreen 12.1" (30 cm) full color touchscreen display Ink System 200ml ink cartridge Low Ink Indicator Warning messages alert user on the printer and touchscreen, LED light beacon optional Substrate Capabilities Porous or Non-Porous surfaces Electrical Requirements 90 - 264 VAC, 50/60 Hz     Operating Environment 34°F - 104°F (1° - 40°C)     Storage Environment 0°F - 140°F (-18° - 60°C)    Agency Certifications UL, CE, and CSA certified 

Squid Ink’s CoPilot uses proven Xaar piezo technology to print up to .7” of hi-resolution characters, razor-sharp text, scannable bar codes, and great looking logos at 185 dpi and a 4.3″ full color touchscreen provides access to the system’s internal messages and print functions. Messages are created and edited on Squid Ink’s easy-to-use Orion™ PC Software and transferred via Ethernet or USB device. For larger applications, multiple CoPilot printing systems can be connected via Ethernet or wirelessly and controlled through one central Orion print station.     Print Technology Piezo impulse printhead technology Maximum Print Height .7" (1.8cm) per printhead Vertical Print Resolution 185 dpi capable of printing razor-sharp graphics, small character text, and scannable bar codes Horizontal Print Resolution 205 dpi Print Speed Up to 135 feet/min. (41 m/min.) @ 205 dpi Time & Date Internal real time clock with battery back-up Product Sensor External photocell. Optional encoder Communication Interface One USB host and one Ethernet input Touchscreen 4.3″ (10.9 cm) full color touchscreen display Ink Cartridge Volume 200ml Integrated Ink System Allows mechanical rotation of printhead to accommodate tilt conveyors or web applications; 0-90degrees counterclockwise; 0-45 degrees clockwise (ink cartridge facing up) Low Ink Indicator Message alert on touchscreen, LED light beacon optional Substrate Capabilities Porous or Non-Porous surfaces Electrical Requirements 100 - 240 VAC, 50/60 Hz    Operating Environment 34°F - 104°F (1° - 40°C)    Storage Environment 0°F - 140°F (-18° - 60°C)    Agency Certifications CE, TUV pending  

The SQ/2 large character ink jet system prints high quality dot-matrix characters on a variety of products at a cost-effective price. The SQ/2 offers the lowest price per printed character in the industry today. Users can choose between two models: a water-based model for printing on porous surfaces like corrugated cartons, or as a solvent-based system for printing on non-porous product like plastics, stretch wraps, metals and more. Printer Type Large character ink jet printer Character Height .75″ (1.9cm) in 7 x 5 matrix; .5″ (1.3cm) in 5 x 5 matrix, or.5″ (1.3cm) in 7 x 5 matrix; .375″ (1cm) in 5 x 5 matrix, or.375 (1cm) in 7 x 5 matrix; .25 (.6cm) in 5 x 5 matrix  Character Set 61 character ASCII set Print Speed 20 feet/minute (6.1m/minute) to 200 feet/minute (61m/minute) line speed; optional extended characterwidth firmware allows for print speeds slower than 20 feet/minute Message Length 60 characters per message; 64 memory locations Communication RS-232C, 9600 baud, 8 data bits, 1 start, 1 stop, Asynch Software Features 24-hour clock, Julian date, counter, lot counter Operating Features Dot size, print delay, character width, photocell on/off, invert print, reverse print, purge routine SQ/2 Exchange Program Eliminates the need for costly service calls and minimizes downtime; troubled printheads andcomponents can be replaced in less than 5 minutes Controller Dimensions 12″ (31cm) H x 12″ (31cm) W x 5.25″ (13cm) D Controller Weight 10.5 lbs. (4.8kg) Printhead Dimensions 3″ (7.6cm) H x 1.6″ (4.1cm) W x 7″ (17.8cm) L; dimensions are for the printhead only – an additional3″ (7.6cm) is needed for the ink line and cabling which extends from the back of the printhead  Product Sensor Diffuse beam photocell (24v) or hardware sinking signal  Electrical Requirements 110/120 VAC, 50/60Hz, 1.6 amp Cabinet Construction Industrial gauge coated steel Operating Environment 38°F (3°C) to 122°F (50°C) Substrate Capabilities Porous or Non-Porous surfaces Air Requirements No external air needed Ink Capabilities Porous: Squid Ink SQ-60™ no-clog inkNon-Porous: Several Squid Ink solvent based fluids to meet adhesion and dry time needs Ink Volume .5 (1.89 liters) gallon bottle standard; available upgrade (water-base ink only) to 5.0 gallon pail(18.93 liters 

The SQ/2 Scorpion industrial large character ink jet printer includes upgraded software delivering more features. SQ/2 Scorpion users have the option of choosing from several print head configurations. Five different print head sizes are available, offering 12 print sizes ranging in height from 3/8" up to 1 3/4". The 1600 Series print heads offer split-line capability and the option of printing full-size characters or half-size characters with the same print head.SQ/2 Scorpion Printing System Specifications     Printer Type Large character ink jet printing system Printhead Options Users have the option to use up to:two SQ/2 printheads, or one 1600 Series printhead Character Heights SQ/2 Series Printheads (7-channel dot matrix characters)• .75" (1.9cm) in 7 x 5 matrix; .5" (1.3cm) in 5 x 5 matrix, or• .5" (1.3cm) in 7 x 5 matrix; .375" (1.0cm) in 5 x 5 matrix, or• .375" (1.0cm) in 7 x 5 matrix; .25" (.6cm) in 5 x 5 matrix1600 Series Printheads (16-channel dot matrix characters)• 1.75" (4.5cm) in 16 x 10 matrix, with split-line capabilityto print two lines of the following size characters: .75" (1.9cm)at 7 x 5 matrix; .5" (1.3cm) in 5 x 5 matrix, or• 1.0" (2.5cm) in 16 x 10 matrix, with split-line capabilityto print two lines of the following size characters: .375" (1.0cm)at 7 x 5 matrix; .25" (.6cm) in 5 x 5 matrix Character Set 61 character ASCII set Print Speed Up to 200 feet/minute (61m/minute) line speed Message Length 128 character length per message; 128 memory locations Communication RS-232C, 9600 baud, 8 data bits, 1 start, 1 stop, Asynch Software Features Counter, lot counter, 24-hour clock, 8 or 12 hour programmableshift code, Julian date, 3-letter month name, 3-letter weekday name,expiration date, expiration month, expiration day, expiration year,expiration Julian date Operating Features Dot size, print delay, character width, photocell on/off, invert print, reverse print, purge routine Shaft Encoder Output Resident software allows communication with shaft encoder for usewith variable speed conveyors Component Modularity Eliminates the need for costly service calls and minimizes downtime;printheads and components can be replaced in less than 5 minutes Controller Dimensions 12" (31cm) H x 12" (31cm) W x 5.25" (13cm) D Controller Weight 10.5 lbs. (4.8kg) Printhead Dimensions SQ/2 Series Printheads: 3" (7.6cm) H x 1.6" (4.1cm) W x 7" (17.8cm) L1600 Series Printheads: 2.5" (6.4cm) H x 1.5" (3.8cm) W x 7" (17.8cm) LDimensions are for the printhead only – an additional 3" (7.6cm) isneeded for the ink line and printhead cabling which extends from theback of the printhead Product Sensor Diffuse beam photocell (24v) or hardware sinking signal Communication Interface Two RS-232 ports for connection to input device, host PC,and PLC for input from scale, scanner or external alarm Air Pump Internal air pump module provides necessary air pressure;external air not recommended Electrical Requirements – 90-120 VAC, 50/60Hz, 4.0 amp Cabinet Construction Industrial gauge coated steel Operating Environment Water-Based Ink: 32oF (0oC) to 120oF (50oC)Solvent-Based Ink: 0oF (-18oC) to 120oF (50oC) Substrate Capabilities Porous or Non-Porous surfaces     Ink Capabilities Porous: Squid Ink SQ-60 no-clog inkNon-Porous: Several Squid Ink solvent based fluids to meet yourapplication needs for adhesion and dry time      Ink Volume .5 gallon (1.9 liters) bottle standard; available upgrade(water-base ink only) to 5.0 gallon (18.9 liters) pail